DMX LED strip Controller ST802SE supports a variety of single or double-line driver chips. It can drive a maximum of 6144 pixels with four ports and has an infrared remote control and display functions. Controller ST802SE can address many DMX512 chips.
Supported LED Strip IC For Controller ST802SE:
LPD6803, LPD8806, LPD6813, LPD1882, LPD1889, LPD6812, LPD1883, LPD1886, DMX512, APA102, UCS6909, UCS6912, UCS1903, UCS1909, UCS1912, WS2811, WS2812, TM1803, TM1804, TM1809, TM1812, TM1829, TA9912, TM1913, TM1914, TM1926, WS2801, WS2803, DZ2809, P9813, P9816, SM16716, LD151x, LD153x, MBI6021, MBI6023, MBI6024, INK1003, LX1003, LX2003, LX2006, TLS3001, TLS3002, etc. Auxiliary software is “LED Build Software“.
Performance Controller ST802SE:
- Controller ST802SE has four ports; each port controls a maximum of 1536 pixels
- Input voltage is 5 to-rw 24 volts DC.
- SD card supports FAT32, FAT16 format, maximum allowed capacity is 64GB, stores up to 64 DAT files.
- The speed range is 1 to 50 frames per second, clock frequency range is 0.1MHZ to 2.5MHZ.
- ST802SE has infrared remote control and nixie tube display functions.
Remote Control Operation:
Switch DAT file:
Press “file” to enter file mode, nixie tube will display the DAT file number. Press “+” or “－” to switch to the next or previous file; You can still use the digital keys to enter the DAT file name you want to play and press “confirmation” to switch to the file.
Set clock frequency:
Press “clock” to display the current clock, which includes an integer part and a decimal part, the unit is MHZ. You can change the clock by pressing “+” and “－”, can also set the clock by using the digital keys, then press “confirmation” to confirm.
Set play speed:
The play speed range is 1 to 200, the unit is a frame per second. Enter a number with digital keys, press “confirmation” to confirm and save, you can also use the “+”, and “－” keys to increase or decrease speed.
Playing mode selection
H805SB defaults to playing files on an SD card recurrently, you can choose to play a single file continuously.
“All Playback” is continuously playing all DAT files in a cycle.
“Select Playback” is playing a single DAT file.
Color modulation
Press “Select” to enter color modulation mode, then press “selection” to adjust the brightness of blue, press “select playback” to adjust the brightness of green, and press “all playback” to adjust the brightness of red. Particularly, LPD6803 and LPD8806 don’t support color modulation functions.
Button Operation:
Four buttons: “SET”, “Mode”, “ + ”, “－”.
SET: Save parameters
Mode: press to switch mode. There are three modes: file mode(display “F”), speed mode(display “P”), and clock mode(display “C”).
“ + ” and “－”: plus and minus.
Notes:
(1). Power controller on, the controller will first display “2SE”, then display file number “F01”(if SD card is inserted and data is valid). Without an SD card, the controller will blink “Sd”.“F0”: no valid DAT file on the SD card. “FE”: controller type is wrong or pixels number is beyond a limit. “RE”: reading SD card failed.
(2). Press “Set” to save the value.
(3). SD card must be formatted into FAT16 or FAT32 after many times of deletions.
(4). In LED Build Software, the controller type is “SE”, choose “four-line with a slave”.
(5). Buttons are used to switch files, set speed, and clock. “Single playback” or “ All playback” is set by remote control.
